Description
- [High Power Output] The Renogy Black Division 100W Lightweight Monocrystalline Solar Panel can provide an average of 500 Watt-hours of electricity per day (depending on sun availability).
- [Easy to Transport, Carry and Install] The solar panel suits most curved surfaces as it is bendable within 240 degrees. It weighs only 1/3 of the rigid panel and presents an all-black glare-free appearance.
- [Industry-leading Tech] It is equipped with half-cut PERC cell technology that enhances solar light capture and electrical performance, therefore improving the output efficiency.
- [Reliable & Durable] This solar panel accomplishes with IP67 rated waterproof junction box and solar connectors. Withstand up to 5400 Pa of heavy snow load and up to 2400 Pa of high wind.
- [Ready for Installation] The panel comes with pre-drilled mounting holes and 2.3 feet long solar connector cables for quick and easy installation.
Henry Heistand –
The original order was lost by Australia Post – but – Renogy sent a replacement via a different carrier.
They were more helpful than Amazon.
The panel is a replacement for a 110W flexible panle and the Renogy 100W has greater output – VERY Happy with it.
Lee G –
Open Voltage and short circuit current match specs. DVM showed 20.1V/6A on a mostly cloudy day.
Fits perfectly in the spot I imagined keeping it.
Other thoughts: Good thing this is a flexible panel as USPS tried to bend the box for me to prove it would flex.
Ed B. –
These panels are great so far. Built to last. A quality product! My favorite so far.
Dan Tocher –
I’m out this on my RV and it worked out perfectly. It flexes nice with no cracking like some of the other Cheaper models.
Lee G –
Works great I have it paired with an anker powerhouse and it charges it easy. Have it mounted on my truck cap, flexible, sleek and light.
MtnSoar –
I am using this panel as a portable-not permanently installed- solar input for my pop up camper. The Renogy Solar100W 12V Lightweight Semi Flexible Black Panel is durable and lightweight. I am getting 90w-5.2 amps out of this little panel on average. That is pretty good efficiency for a small flex panel! The small size allows me to place the panel on the dash of my parked and locked truck- which is nice for trickle charging my 200ah lithium battery system while I am away on a hike. The ability to easily store this panel just about anywhere in my truck or pop up camper is a great bonus to it’s usefulness. I have tried a couple knock off-cheap flex panels and they are not as efficient or durable as this panel. It’s worth the few extra dollars to get the quality results this panel provides. When my non-Renogy rooftop 200w solar panel needs replacing I will definitely use a Renogy glass panel.
Solar Traveler –
received on time and in good order. Have not used it yet but looks good quality and I am confident it will do the job charging my lithium batteries.
TM –
Most of the flexible panels I’ve tried did not put out but this one has much better output.
MtnSoar –
The panels perform well seem durable and are flexible. I’m very pleased with them. They fit the bill for my application. Small amounts of shade do not seem to significantly impact the panels’ output, unlike some i’ve used.
I needed low-profile flexible panels to fit on my truck’s topper, between the roof racks. The size of the panels are a perfect fit, and allow 2 to be installed on my roof. I wanted the installation to be easily removable, but to also easily handle highway speeds without me worrying about panels flying off. Utilizing the grommets on the panels allowed me to use M6 tee nuts and M6 machine screws and 1” M6 threaded plastic knobs to hold the panels in place. The grommet placement on the 2 panels I received were identical. I fit the machine screws through holes drilled in the topper. The screws (and large washers) are on the inside of the topper, with the tee nuts on the outside. The screws and nuts are snugly tightened, which allows the plastic knobs to be loosened and tightened without someone inside the topper holding a screwdriver to keep the screws from loosening. I used RTV to seal the holes, which also helps hold the screws and nuts in place without turning. I’ve used similar combos on truck toppers for 30+ years and have never had water leaks.
I also attached heavy duty velcro around the edges of the panels, and attached velcro to the topper. The velcro alone holds the panels very well, but I wanted more security for highway speeds, hence the tee nuts and machine screws. I also put a “carbon fiber” looking vinyl wrap on the topper where the panels fit, for abrasion protection. Insulation can be placed under the panels to insulate the topper from the panels, which can get hot. 5 mm foam insulation is what I use.
TM –
Needs to be permanently mounted.
Purchased the thin flexible Renogy 100 watt solar panel for charging a RV battery bank. It is light in weight and easily produces the specified power. In the process of moving the panel it was twisted slightly diagonally and you could hear something pop. It now produces half the specified power. Used the panel less than a year. Panel is too fragile to be used as a portable device.
Panel can bend top to bottom. Not diagonally.